...

SAE 8620 Steel

aisi 8620 round bar

WALDUN is one of the best SAE 8620 steel Manufacturers and Exporters, supplied with round,square,flat,block,and shaft etc.

SAE 8620 is defined as low carbon alloy steel which has 0.5% Cr, 0.2% Mo and 0.5% Ni as strengthening alloy elements.It is generally supplied as annealed condition with hardness HB255max.

SAE 8620 has good wear resistant with case hardness HRC 60-63  when carburized, hardened and tempered.Compared with grades 8615 and 8617, it shows good core strength and toughness properties with a typical tensile strength range of 700-1100 MPa,in small to medium sized sections.
SAE 8620 is suited for applications which require a combination of toughness and wear resistance. it is commonly used in the engineering and automitive industries for toolholders and other such components.
Typical application:Arbors, pinions, bushes, camshafts, kingpins,ratchets, gears, splined shafts etc.

SAE 8620 Steel Supply Form & Size & Tolerance

Supply Form Size(mm) Process Tolerance
Round Φ6-Φ100 Cold Drawn Bright/Black Best H11
Φ16-Φ350 Hot Rolled Black -0/+1mm
Peeled/ground Best H11
Φ90-Φ1000 Hot Forged Black -0/+5mm
Rough Turned -0/+3mm
Flat/Square/Block Thickness :120-800 Hot Forged Black -0/+8mm
Width:120-1500 Rough Machined -0/+3mm

Remark:Tolerance can be customized as per requests

SAE 8620 Steel Chemical Composition per ASTM A29

GRADE C Si Mn P S Cr Mo Ni
8620 0.18-0.23 0.15-0.35 0.70-0.90 ≤ 0.035 ≤ 0.040 0.40-0.60 0.15-0.25 0.40-0.70

 SAE 8620 Steel Physical Property

Density g/cm3 7.85
Melting point Deg F 2600
Poisson’s ratio 0.27-0.30
Machinability (AISI 1212 as 100% machinability) 65%
Thermal expansion (20 ºC)(ºC ˉ ¹) 12.2*10^-6
Specific heat capacity J/(kg*K) 477
Thermal conductivity W/(m*K) 46.6
Electric resistivity Ohm*m 2.34*10^-7

SAE 8620 Steel Mechanical Property

Typical Mechanical Properties For Core – Carburised and Oil Quenched at 840  °C

Section Size 11mm 30mm 63mm
Tensile Strength Mpa 980-1270 780-1080 690-930
Yield Strength Mpa ≥785 ≥590 ≥490
Elongation % ≥9 ≥10 ≥11
Charpy Impact J ≥41 ≥41 ≥41
Hardness HB 290-375 235-320 205-275
Hardness HRC 31-41 23-35 16-29

SAE 8620 Steel Hardenability Limits

Distance from quenched end mm 1.5 3 5 7 9 11 13 15 20 25 30 35 40
HRC Min 41 37 31 25 21
HRC Max 48 47 43 39 35 32 30 29 26 24 23 23 23

Hardness values under 20HRC  is not specified.

SAE 8620 Steel Forging

Forging temperature should be carried out between 925℃-1230℃,AISI 8620 has low carbon content  which is  less susceptible to cracking than medium or high carbon steels,so  it may be heated and cooled more rapidly.Soaking time at forging temperature should be as short as possible to avoid heavy scaling and excessive grain growth.The lower the forging-ending temperature ,the finer the grain size .Don’t forge below minimum forging temperature 850°C.This alloy should be cooled in sand.

SAE 8620 Steel Normalizing

Normalizing is used to refine the structure of forgings that might have cooled non-uniformly after forged,and considered as a conditioning treatment before case hardening.Normalizing temperature for AISI 8620 steel should be carried out between 900℃-925℃. hold suitable time for the steel to be thoroughly heated to complete the ferrite to austenite transformation.Cool in still air.This treatment is considered as another method of improving machinability.

SAE 8620 Steel Annealing

Full annealing is recommended  for AISI 8620 before machining, AISI 8620  should be carried our at a nominal temperature of 820℃-850℃,hold suitable time for the steel to be thoroughly heated, then furnace cooling.

SAE 8620 Steel Case Hardening

Following core refining, Heat the temperature to 780oC – 820oC, hold suitable time for the steel to be thoroughly heated, and quench in oil.Temper as soon as possible after quenched.

SAE 8620 Steel Tempering

Tempering is usually carried out to relieve stresses from the hardening process,it will improve the toughness of both case and core, with only a little reduction in core strength and case hardness.Heat the AISI 8620 steel to 150oC – 200oC as required, hold enough time until temperature is uniform throughout the section, soak for 1 – 2 hours per 25 mm of section, and cool in still air.

SAE 8620 Steel Caburizing

Pack, salt or gas carburize at temperature  900oC – 925oC, holding enough  time to obtain the required case depth and carbon content, followed by a suitable hardening and tempering cycle to optimise case and core properties.

Certificate & Third-party Testing

SAE 8620 MTC Report

TUV Testing Report

Latest Products

CONTACT WALDUN STEEL

Mobile:

+8618652469606

Email:

iguhongtao@gmail.com

waldun steel iso 9001 logo 300x158

Get A Quote Now !

© Copyright - WALDUN STEEL