C40E (din 1.1186) Steel<\/strong><\/h1>\n![\"C40E](\"https:\/\/waldunsteel.com\/wp-content\/uploads\/2021\/10\/C40E-din-1.1186-Steel-1030x610.jpg\")
<\/p>\n
WALDUN is one of the best company in China to manufacture and supply C40E (din 1.1186) steel.From casting, forging, steel to hot and cold rolling process, heat treatment, etc, Waldun\u00a0have the control of professional engineers. We have advanced precision machining equipment, according to the requirements of users machining. in order to achieve the most satisfied with the user requirements.<\/p>\n
\u00a0C40E (din 1.1186) Steel<\/strong>\u00a0Details:<\/strong><\/h2>\nC40E (din 1.1186) Steel\u00a0Surface conditions: scaled (hot working finish)\/ground\/rough machining\/fine machining\/based on the customer’s requirement<\/p>\n
Furnaces for metallurgical processing: electrode arc + LF\/VD\/VOD\/ESR\/Vacuum consumable electrode.<\/p>\n
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer’s requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.<\/p>\n
We serve you with our honesty, integrity, and professionality.<\/p>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Applications<\/strong><\/h2>\nUsed for crankshafts, couplings and cold headed parts.<\/p>\n
Physical properties (avarage values) at ambient temperature
\nModulus of elasticity [103<\/sup>\u00a0x N\/mm2<\/sup>]: 210
\nDensity [g\/cm3<\/sup>]: 7.84<\/p>\nSoft Annealing
\nHeat to 870-980o<\/sup>C, cool slowly in furnace.<\/p>\nNormalizing
\nNormalizing temperature: 890o<\/sup>C.<\/p>\nStress Relieving
\nStress relieving to remove machining stresses should be carried out by heating to approx. 590o<\/sup>C, holding for 1-2 hours at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.<\/p>\nHardening
\nHarden from a temperature of 840-898o<\/sup>C followed by water quenching.<\/p>\nTempering
\nTempering from the quenched condition may be done at 320 to 700o<\/sup>C depending upon the strength desired.<\/p>\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Forging<\/strong><\/h2>\nHot forming temperature: 1100-850o<\/sup>C.<\/p>\n\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Machinability<\/strong><\/h2>\nMachinability is good, rated at 60% that of the AISI 1112 alloy used as a 100% machining rated\u00a0steel.<\/p>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Corrosion Resistance<\/strong><\/h2>\nThis is a\u00a0steel\u00a0alloy and will rust if not protected. it is not corrosion resistant.
\n
\n<\/strong><\/p>\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Welding<\/strong><\/h2>\nCK40\u00a0steel\u00a0is weldable by all of the welding methods. However with its higher carbon content it is important to use both pre-heat at 150 to 260o<\/sup>C and post-heat at 590 to 650o<\/sup>C practice per an approved welding procedure.<\/p>\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Cold working<\/strong><\/h2>\nIn the annealed state the CK40 alloy is readily cold worked by conventional methods.<\/p>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Mechanical properties<\/strong><\/h2>\nC40E (din 1.1186) Steel standards to meet the 1.1186, DIN Ck40, AISI 1040 mechanical performance, can also according to the customer request, to meet the requirements of customers of 1.1186, DIN Ck40, AISI 1040 mechanical properties.<\/p>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Heat treatment<\/strong><\/h2>\n1.1186, DIN Ck40, AISI 1040 Heat treatment,Our production completely according to the 1.1186, DIN Ck40, AISI 1040 standards to meet the 1.1186, DIN Ck40, AISI 1040 Heat treatment, can also according to the customer request, to meet the requirements of customers of 1.1186, DIN Ck40, AISI 1040 Heat treatment.<\/p>\n<\/div><\/section><\/div>
\n<\/div><\/section>
\nLatest Products<\/h3>
<\/p>\nC40E (din 1.1186) Steel\u00a0Surface conditions: scaled (hot working finish)\/ground\/rough machining\/fine machining\/based on the customer’s requirement<\/p>\n
Furnaces for metallurgical processing: electrode arc + LF\/VD\/VOD\/ESR\/Vacuum consumable electrode.<\/p>\n
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer’s requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.<\/p>\n
We serve you with our honesty, integrity, and professionality.<\/p>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Applications<\/strong><\/h2>\nUsed for crankshafts, couplings and cold headed parts.<\/p>\n
Physical properties (avarage values) at ambient temperature
\nModulus of elasticity [103<\/sup>\u00a0x N\/mm2<\/sup>]: 210
\nDensity [g\/cm3<\/sup>]: 7.84<\/p>\nSoft Annealing
\nHeat to 870-980o<\/sup>C, cool slowly in furnace.<\/p>\nNormalizing
\nNormalizing temperature: 890o<\/sup>C.<\/p>\nStress Relieving
\nStress relieving to remove machining stresses should be carried out by heating to approx. 590o<\/sup>C, holding for 1-2 hours at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.<\/p>\nHardening
\nHarden from a temperature of 840-898o<\/sup>C followed by water quenching.<\/p>\nTempering
\nTempering from the quenched condition may be done at 320 to 700o<\/sup>C depending upon the strength desired.<\/p>\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Forging<\/strong><\/h2>\nHot forming temperature: 1100-850o<\/sup>C.<\/p>\n\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Machinability<\/strong><\/h2>\nMachinability is good, rated at 60% that of the AISI 1112 alloy used as a 100% machining rated\u00a0steel.<\/p>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Corrosion Resistance<\/strong><\/h2>\nThis is a\u00a0steel\u00a0alloy and will rust if not protected. it is not corrosion resistant.
\n
\n<\/strong><\/p>\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Welding<\/strong><\/h2>\nCK40\u00a0steel\u00a0is weldable by all of the welding methods. However with its higher carbon content it is important to use both pre-heat at 150 to 260o<\/sup>C and post-heat at 590 to 650o<\/sup>C practice per an approved welding procedure.<\/p>\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Cold working<\/strong><\/h2>\nIn the annealed state the CK40 alloy is readily cold worked by conventional methods.<\/p>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Mechanical properties<\/strong><\/h2>\nC40E (din 1.1186) Steel standards to meet the 1.1186, DIN Ck40, AISI 1040 mechanical performance, can also according to the customer request, to meet the requirements of customers of 1.1186, DIN Ck40, AISI 1040 mechanical properties.<\/p>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Heat treatment<\/strong><\/h2>\n1.1186, DIN Ck40, AISI 1040 Heat treatment,Our production completely according to the 1.1186, DIN Ck40, AISI 1040 standards to meet the 1.1186, DIN Ck40, AISI 1040 Heat treatment, can also according to the customer request, to meet the requirements of customers of 1.1186, DIN Ck40, AISI 1040 Heat treatment.<\/p>\n<\/div><\/section><\/div>
\n<\/div><\/section>
\nLatest Products<\/h3>
\nModulus of elasticity [103<\/sup>\u00a0x N\/mm2<\/sup>]: 210
\nDensity [g\/cm3<\/sup>]: 7.84<\/p>\n
Soft Annealing Normalizing Stress Relieving Hardening Tempering Hot forming temperature: 1100-850o<\/sup>C.<\/p>\n Machinability is good, rated at 60% that of the AISI 1112 alloy used as a 100% machining rated\u00a0steel.<\/p>\n This is a\u00a0steel\u00a0alloy and will rust if not protected. it is not corrosion resistant. CK40\u00a0steel\u00a0is weldable by all of the welding methods. However with its higher carbon content it is important to use both pre-heat at 150 to 260o<\/sup>C and post-heat at 590 to 650o<\/sup>C practice per an approved welding procedure.<\/p>\n In the annealed state the CK40 alloy is readily cold worked by conventional methods.<\/p>\n C40E (din 1.1186) Steel standards to meet the 1.1186, DIN Ck40, AISI 1040 mechanical performance, can also according to the customer request, to meet the requirements of customers of 1.1186, DIN Ck40, AISI 1040 mechanical properties.<\/p>\n 1.1186, DIN Ck40, AISI 1040 Heat treatment,Our production completely according to the 1.1186, DIN Ck40, AISI 1040 standards to meet the 1.1186, DIN Ck40, AISI 1040 Heat treatment, can also according to the customer request, to meet the requirements of customers of 1.1186, DIN Ck40, AISI 1040 Heat treatment.<\/p>\n<\/div><\/section><\/div>
\nHeat to 870-980o<\/sup>C, cool slowly in furnace.<\/p>\n
\nNormalizing temperature: 890o<\/sup>C.<\/p>\n
\nStress relieving to remove machining stresses should be carried out by heating to approx. 590o<\/sup>C, holding for 1-2 hours at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.<\/p>\n
\nHarden from a temperature of 840-898o<\/sup>C followed by water quenching.<\/p>\n
\nTempering from the quenched condition may be done at 320 to 700o<\/sup>C depending upon the strength desired.<\/p>\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Forging<\/strong><\/h2>\n
\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Machinability<\/strong><\/h2>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Corrosion Resistance<\/strong><\/h2>\n
\n
\n<\/strong><\/p>\nC40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Welding<\/strong><\/h2>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Cold working<\/strong><\/h2>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Mechanical properties<\/strong><\/h2>\n
C40E (din 1.1186) Steel<\/strong>\u00a0<\/strong>Heat treatment<\/strong><\/h2>\n
\nLatest Products<\/h3>
![\"1.2358\"](\"https:\/\/waldunsteel.com\/wp-content\/uploads\/2024\/01\/1.2358-36x36.jpg\")
<\/a>![\"sae](\"https:\/\/waldunsteel.com\/wp-content\/uploads\/2021\/04\/SAE-1045-Carbon-Steel-Round-Bars-36x36.jpg\")
<\/a>![\"Steel-C60r-1-1223-Bar-or-Rod-for-Project\"](\"https:\/\/waldunsteel.com\/wp-content\/uploads\/2021\/08\/Steel-C60r-1-1223-Bar-or-Rod-for-Project-36x36.jpg\")
<\/a>![\"waldun](\"https:\/\/waldunsteel.com\/wp-content\/uploads\/2022\/05\/Waldun-Steel-ISO-9001-Logo-300x158-1.png\"){kind=logo}